CTP Tech
InTheGarageMedia.com
A mechanic's hands adjusting the throttle linkage on a chrome JEGS carburetor mounted inside an engine bay.
FE Fuel Redo
FE Fuel Redo
Revitalizing and Upgrading a 1967-72 Bumpside Ford Fuel System
BY RYAN MANSON IMAGES BY RYAN FOSS
I

’m sure we all have a story (or 10!) about the one that got away. You know the one; that first love from “semester” year. Tan on green on 17s … something like that. For our buddy Tim Foss, when he had the opportunity to buy back a long-lost friend in the form of a 1972 Ford F-100, he knew it was his chance to relive a teenage dream, this time via an adult’s budget. But before he simply started throwing cash at the truck, he knew he wanted to get it up and running. The FE motor looked good and a quick inspection revealed she should be a strong runner, so it was decided to start there, beginning with the fuel system.

With a list of parts in hand, we logged onto the JEGS website, knowing that their vast inventory would likely contain everything we would need—and we weren’t wrong! From the gas tank to the air cleaner, we created a parts list that would allow us to freshen up the entire fuel system without concession. From a truck that barely ran that morning to that afternoon when it was fueled up, fired up, and ready for a shakedown cruise around the neighborhood. Back behind the wheel of his high school dream ride we could see the excitement in Foss’ eyes.

While this project is only getting started, getting her up and running is a huge step in the right direction. And it couldn’t have been any easier, thanks to the guys at JEGS and their helpful customer service and parts availability.

Dust and sand accumulation inside cab.
1. Due to the truck’s location over the last couple decades, a large accumulation of dust and sand has found its way inside the cab. Unfortunately, it also found its way inside the fuel tank (and the gauges, the glovebox, the seat, under the carpet, inside the headliner). Not wanting to run the risk of possibly contaminating any new parts, we opted to replace the original tank with a new one from JEGS’s Restoration Line.
Lifting original gas tank.
Dirty old gas tank.
2-3. Pulling the stock tank is a pretty straightforward affair, consisting of disconnecting the fuel line, filler neck, and fuel level sending unit wires, unbolting the tank from the cab, and lifting it free and clear.
New reproduction 19.5-gallon fuel tank.
4. While it is certainly possible to clean and treat the original tank and put it back to use, time is not on our side, so it made more sense to simply log onto jegs.com and order what we needed. In our case, they offered a direct-fit reproduction 19.5-gallon fuel tank (PN 555-78213) constructed from galvanized steel with a zinc-coated finish. Doesn’t get any easier than a drop-in replacement!
Fuel tank sending unit opening.
5. JEGS’s fuel tank is compatible with the stock fuel level sending unit as well as aftermarket and will also accept the stock fuel hard line.
New filler neck, hose, and clamps.
6. We also ordered a new filler neck (PN 555-78285), hose (PN 555-15996), and clamps (PN 555-16051), which will allow us to refresh the fuel system up to the fuel pump and beyond.
New fuel tank installed.
7. True to claim, JEGS’s tank dropped right in place and lined up with the factory fasteners.
New fuel level sending unit.
8. While the original sending unit could have been used, we figured that while we were at it, we might as well replace that too (PN 106-881-4561).
Sending unit and hardline installed.
Overview of tank and hardline.
9-10. With the tank installed, you can see the filler level sending unit and original hardline attached.
8. While the original sending unit could have been used, we figured that while we were at it, we might as well replace that too (PN 106-881-4561).
9-10. With the tank installed, you can see the filler level sending unit and original hardline attached.
Installing filler neck.
Inserting fuel neck into grommet.
Chrome fuel cap.
11-13. The replacement filler neck attaches to the tank with a short section of hose cut to length so that the neck protrudes just past the JEGS grommet (PN 106-891-4570-1). A Gates fuel cap (PN 465-31623) is the finishing touch.
Dirty FE engine with 2-barrel carb.
Removing old carburetor.
14-15. Out of the cab, our attention is turned to the engine-side of things. We’re going to be swapping out the old 2-bbl carb and intake along with a few other upgrades, so there’s a handful of parts that need to be removed, disconnected, and discarded; starting with the carburetor.
FE engine with intake removed.
New pushrods and carburetor on bench.
16-17. An intake manifold swap on a traditional small-block can be a pain, with all the gasket and RTV scraping and cleaning required, draining the coolant, and so on, but an FE intake manifold swap takes the traditional task and says, “hold my beer.” For those not in the know, the FE engine design finds the pushrods traveling through voids in the intake, requiring the entire valvetrain assembly to be removed before the intake can be. Luckily, the pushrods are not adjustable!
Lifting heavy cast-iron intake manifold.
18. Pulling an FE cast-iron intake can require a cherry picker as they are heavy! Luckily, I’ve been working out knowing that this job was in my future, so my forearms were prepared. My back, not so much!
New intake, carburetor, and gaskets on table.
19. Laid out for bare are the parts that will consist of our fuel system upgrade. From left is a JEGS dual-plane intake manifold in black (PN 555-513096) and a JEGS 600-cfm Street Fighter carb (PN 555-16650) along with a variety of gaskets and hardware to complete the installation.
JEGS Street Fighter four-barrel carburetor.
20. JEGS’s Street Fighter carburetor is a square-bore, four-barrel design and features external float adjustment with float/fuel level sight glasses, down leg boosters, single inlet, and an electric choke for easy cold starting. Ported (timed) and manifold vacuum ports are also present.
Carburetor jets and installation hardware.
21. With a primary jet size of 98 and a secondary jet size of 95, the Street Fighter carb is set up for most mild performance street engines. However, if one is wont to tinker, all carbs are shipped with additional jets as well, making fine-tuning capable. Carb and air cleaner studs, port plugs, gasket, and electric choke wiring harness are also provided.
Lowering new aluminum intake manifold.
22. Using the provided JEGS gaskets, gasket adhesive, and RTV sealant where applicable, the new intake manifold is lowered in place. Note the use of a cherry picker is not necessary thanks to the lighter aluminum design of the JEGS intake.
Placing carburetor on intake.
23. Next, the Street Fighter carb is set in place.
Powder-coated black valve cover.
Installing new black valve covers.
24-25. We decided to add a little lipstick to the dirty pig in the shape of a pair of black powdercoated steel valve covers from JEGS (PN 969-8346). A matching air cleaner (PN 555-500054) will be added a little later.
Mounting new throttle pedal bracket.
Tightening throttle pedal bolts.
26-27. Back inside the cab, we’re installing a new Lokar billet aluminum throttle pedal from JEGS (PN 625-BAG-5212) designed specifically for this era Ford truck as a direct bolt-in using factory hardware.
Overview of new throttle pedal.
Drilling hole through firewall.
Completed throttle pedal installation.
28-30. The Lokar pedal bracket also features a hole for the throttle cable that will be used as a template, allowing us to drill through the firewall in the precise spot. This will allow for a Lokar throttle cable to be used, further simplifying the installation.
Tuning new carburetor on engine.
31. With everything buttoned up, connected, and fluids filled, it’s time to fire up our long-languishing FE and dial the Street Fighter carb in using the idle screw and front mixer screws. A few quick adjustments and the ol’ girl was ready for a spin around the block.
In The Garage Media
JEGS logo

(800) 345-4545
jegs.com
Lokar logo

(865) 824-9767
lokar.com