CTP Tech
InTheGarageMedia.com
Front view of the project 1967 Chevy C10.
1. Here’s the truck as the project began. It is in exceptionally good condition for a vehicle with nearly seven decades of service.
Behind The Scenes
Part 1: BBT Fabrications’ 1967 C10
BY RON COVELL
W

e’re going to take a look at a recent 1967 C10 project built by BBT Fabrications in Mahomet, Illinois. While the body of this truck has been left mostly stock, the detail work done under the skin is truly special, with plenty to draw inspiration from.

The condition of the truck was about as good as could be expected for something nearly 70 years old, but as you’ll see, rust had taken its toll on the cab floor and several other panels. BBT excels in sheet metal fabrication, and you’ll see them work their magic in bringing this truck back to top form.

A Roadster Shop SPEC Series chassis was selected, engineered to accept the C10 components without modification. It includes their custom-designed and fabricated front suspension with rack-and-pinion steering, coupled with a 9-inch rear end and coilover shocks at all four corners. Roadster Shop makes a stainless steel fuel tank for this chassis, sized to tuck neatly under the rear of the bed floor with no modifications required.

A 525hp LS3 engine was selected, paired with a Bowler T56 Magnum transmission, and the BBT crew built a beautiful, all-stainless exhaust system, complete with electrically operated cutouts that exit through the bed just in front of the rear wheels.

Once the cab and bed had been trial-fitted to the chassis and drivetrain, the reconstruction could begin. The entire cab floor was replaced with aftermarket panels, and new sill plates were fabricated from fresh sheet metal. The original rear cab panel was repaired and reused.

The door bottoms were badly rusted, so new metal was shaped to replace them. The inner door panels were reworked to incorporate a modern design, and the audio system speakers were recessed for a cleaner look.

All dents were smoothed out on the bed, cab, hood, and fenders, and several small, rusted areas were replaced with new metal. The metalwork was finished to perfection; it’s impossible to see where the damage once existed.

Once all the fabrication work had been completed, the chassis and suspension components were powdercoated gloss black, while the underhood panels received a satin black finish.

The engine was fitted with vintage valve covers that neatly conceal the modern coil packs, and the underhood area looks exceptionally tidy.

In a future article, we’ll take a closer look at some of the underhood details that make this truck especially impressive.

Roadster Shop SPEC Series bare chassis.
2. A Roadster Shop SPEC Series chassis was selected for the truck.
Chevrolet LS3 engine with black valve covers.
3. The LS3 engine has been fitted with vintage valve covers.
Stainless fuel tank and rear suspension components.
4. A Roadster Shop stainless fuel tank and Wilwood brakes are fitted to the chassis.
T-56 transmission and custom stainless exhaust system.
5. The transmission is a Bowler T-56 Magnum. BBT Fabrications built a beautifully routed stainless exhaust system that tucks in snugly, with nothing hanging below the frame.
Top-down view of exhaust and driveshaft routing.
6. Electrically operated exhaust cutouts are fitted, exiting low in the bedsides.
Exhaust cutout through reinforced frame opening.
7. The exhaust cutout passes through a reinforced opening located under the forward bed mount.
Emergency brake cables routed near chassis cutout.
8. The emergency brake cables are cleanly routed around the cutouts.
Rear view of truck showing exhaust exit.
9. With the bed installed, you can see how the exhaust cutout exits just in front of the rear tire.
Truck bed floor modified with wheel tubs.
10. The bed floor was modified to accept the wheeltubs required for the wide rear tires.
Original engine compartment of the project truck.
11. This “before” view of the engine compartment will be a stark contrast to what comes later.
Rusted interior floor pan before cab restoration.
12. The floor of the cab had a good deal of rust, so it was completely replaced with aftermarket panels.
Repaired and smoothed metal rear cab panel.
13. The rear cab panel had rust and dents, which were expertly repaired by the BBT crew.
Heavily rotted original truck door sill area.
14. Both doorsill plates were badly rotted, so new metal was shaped to replace them.
Fabricating a new metal door sill patch.
15. This is one of the new sill plates under construction.
Finished custom fabricated door sill plate.
16. The right-side sill plate is ready to install.
Fitting new black floor pan in cab.
17. The new floor is being fitted into place.
Fitting firewall and toeboard panels to cab.
18. Here the firewall and toeboard are being fitted.
New metal sill plates welded to cab.
19. The new sill plates fit snugly and have been welded into place.
Rusted lower edge of the original door.
20. The door bottoms also needed repair.
Welding a new metal corner onto door.
21. New metal is carefully shaped and fitted into place.
Repaired door edge before body filler.
22. With the door bottom repaired, it is better than new.
Custom door panel with recessed speaker opening.
23. New custom door panels are being fitted here. Note that the openings for the audio speakers have been recessed for a clean look.
Laser-straight door gaps on the truck cab.
24. The door gaps were adjusted to be laser straight.
Rusted original front fender corner.
25. The front fenders had damage that required repair as well.
Patch panel welded into lower front fender.
26. An aftermarket patch is welded to the lower front edge of the fender.
Fender patch area after initial metal finishing.
27. With some hammer-and-dolly work and light grinding, the seam disappears.
Smooth finished repair on front fender surface.
28. Going over the metal with an orbital sander makes the patch impossible to detect.
Powdercoated chassis ready for components.
29. The chassis has been powdercoated and is ready for assembly.
Black powdercoated control arms and brake parts.
30. All of the suspension and brake components are organized and staged to streamline assembly.
Fully assembled truck chassis with drivetrain.
31. Thanks to good planning, everything fits perfectly together.
Rolling chassis showing rear fuel tank mounting.
32. Here you can see how snug all the components fit within the chassis.
Radiator with dual electric cooling fans.
33. Twin electric fans have been mounted to the radiator, and everything is finished in satin black.
Finished engine bay with orange LS engine.
34. The simple color scheme gives the underhood area a very clean appearance. In a future article, you’ll see how this area is taken to the next level of fit and finish.
In The Garage Media
BBT FABRICATIONS

ROADSTER SHOP logo

(847) 949-7637
roadstershop.com
WILWOOD DISC BRAKES logo

(805) 388-1188
wilwood.com